Trailer Hitch Clearence for the Draw-Tite Class III Trailer Hitch on a 2000 Jeep Grand Cherokee
Question:
Most of these hitches set very low if the jeep did not have the bumper cut out, how high is yours?
asked by: Dave C
Expert Reply:
I went out to the warehouse and measured the Draw-Tite Class III Trailer Hitch, item # 75139 for your 2000 Jeep Grand Cherokee. From the point where the hitch mounting brackets contact the vehicle frame to the top of the hitch receiver the distance is 7-1/8 inches, and the distance from where the hitch mounts to the vehicle frame to the lowest part of the hitch underneath the receiver is 9-3/4 inches.
It is hard to give a height measurement from the ground with the many different tire sizes available and suspension enhancements that are used on vehicles, Jeeps especially. If you measure down from the frame and extend that to the rear you will have a very close approximation of the height that the hitch will end up at.
If you look at the top left portion of the instructions (see link) there is a drawing showing how the hitch should sit once installed.
You can view an installl video by clicking the provided link.
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 7500 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Trailer Hitch Installation - 2003 Jeep Grand Cherokee - Draw-Tite
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Hitch Recommendation for 2004 Jeep Grand Cherokee with Rear Fuel Tank
- Video: Trailer Hitch Installation - 2002 Jeep Grand Cherokee
- Shop: Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: Front Mount Hitch
- Q&A: Does the Draw Tite and Curt Hitch for the 2004 Jeep Grand Cherokee Look the Same Once Installed
- Q&A: Hitch for a 1999 Jeep Grand Cherokee That Does Not Intefere with Spare Tire
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: hitch
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer hitch
- Shop: Brake Controller
- Search Results: 90160
- Video: Choosing the Right Brake Controller
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Recommended Hitch for a 2024 Toyota Grand Highlander
- Article: Trailer Wiring Diagrams
- Shop: Gooseneck Hitch
- Search Results: 5504