Topwind Side Mounted Trailer Jack that Has Wheel Caster

Question

Question:

Is there a manufacturer tube and wheel replacement for the tube and footplate?

asked by: Kb

0

Expert Reply:

The etrailer jack part # TJB-2002-B does not have a wheel caster replacement for the foot of it. The most similar jack we offer that has a wheel caster on the bottom of it instead of a foot is the Dutton Lainson part # DL24MR.

expert reply by: Jameson C

0

Answer 1

If I am understanding your situation properly you are going to have to have the snap ring mount removed from your trailer and then have the part #C28304 welded in place of it so that you can mount the Curt jack. There isn't a way to adapt the…

view full answer...

Answer 2

The inside diameter of the snap ring that would be used for the #TJB-2002-B is 2 inches, and the outside diameter is 2-1/4 inches. We offer the replacement snap ring for that jack as part #SNP-RING

view full answer...

Answer 3

For your Down To Earth Trailer, I recommend the Round Snap Ring Swivel Jack w/ Footplate part #TJB-2002-B. This jack uses a snap ring swivel bracket with a 2-1/2" outer diameter. It should work with the existing bracket you have on your trailer…

view full answer...

Answer 4

From the center of the main mounting section of the Round Snap Ring Swivel Jack #TJB-2002-B to the top of the handle part that connects to the jack is about 5-1/2". The handle then dips down about 1-1/4" while the handle grip sits about…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Topwind Side Mounted Trailer Jack that Has Wheel Caster

Product Page this Question was Asked From

Continue Researching