Are The Power Connections For the Go Power Automatic Transfer Switch # 34264403 AC or DC Power?

Question

Question:

I am looking at the example wiring diagram for the Go Power Automatic Transfer Switch - Plastic Case - 30 Amp - 120V Item # 34264403. On the top left of the switch in the diagram, there is a connection between the transfer switch and the charger. My question is: What kind of power is this connection outputting? Is it a DC output to the charger? Thank you

asked by: Max K

0

Expert Reply:

The power going from the Go Power Automatic Transfer Switch # 34264403 to the charger is 120volt AC power. The charger will put out 12 volt power to the battery. All power connections inside the transfer switch are going to be 120volt AC.

expert reply by: Bud M

0

Wiring Diagram For Go Power Automatic Transfer Switch # 34264403
(click to enlarge)

Answer 1

Yes, you can use the Go Power Automatic Transfer Switch #34264403 in your residential application. You will need to ensure that the electrical being used for your furnace is no more than 30 amps and uses 120 volt power and not 240.

view full answer...

Answer 2

I do have an option for you but none of our power transfer switches will allow you to switch between three AC power sources. However, I do have a way for you to do this but you will need to install two power transfer switches like the Go Power…

view full answer...

Answer 3

The Go Power Automatic Transfer Switch #34264403 that you referenced is a good way to automatically switch between shore power (when available) and an inverter that's being powered by solar charged batteries. It is always going to use shore power…

view full answer...

Answer 4

The Go Power Automatic Transfer Switch #34270278 that you are interested in was designed to automatically switch power sources between an inverter or an AC power source. You'd want to run the inverter you have now to this as well as the power…

view full answer...

Answer 5

You can use the Go Power #34264403 Automatic Transfer Switch for 30 amp service. This transfer switch automatically changes from inverter to shore power when you hook up at the campground. It also protects your electrical system from AC power…

view full answer...

Answer 6

There are a few different brands when it comes to solar power so I recommend finding out exactly which brand of equipment is installed on your RV. You may have an 2-pin XLR style plug in on your camper which would allow you to easily plug in the Go…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 11

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 12

We have one option that will work for you. The Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ uses inner bearing #L68149 and outer bearing #LM67048 so it would work perfectly on your spindle.…

view full answer...

Are The Power Connections For the Go Power Automatic Transfer Switch # 34264403 AC or DC Power?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching