Wiring Needed to Connect Electric Brakes on etrailer 7K Axles to Trailer 7-Way
Question:
I need to replace the axles and the wiring for the brakes on my enclosed car hauler. I need 3 of these 7K drop axles as I was able to verify the measurements you guys have on your site (thank you!) but what wiring do I need?
asked by: Robyn
Expert Reply:
Thanks for reaching out, and I'm glad you were able to determine fitment of the 7K etrailer Drop Axle # e85SR for your car hauler trailer!
The wiring you need to connect all of your electric brakes up to your trailer is 10 gauge wire which we sell by the foot as part # 10-1-1. I also recommend picking up heat shrink butt connectors like part # DW05745-10 to protect your wiring connections from the elements.
If you aren't familiar with how to run your brake wiring I'm adding a photo for you to get a visual. I'm also attaching some review videos for you to check out!
Products Referenced in This Question
Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 10
- Wiring
- Wire Connectors
- Butt Connectors
- 12-10 Gauge
- Deka
more information >
Product Page this Question was Asked From
Trailer Axle w/ Electric Brakes - 4" Drop - 8 on 6-1/2 Bolt Pattern - 94" Long - 7,000 lbs
- Trailer Axles
- Leaf Spring Suspension
- Easy Lube Spindles
- Electric Brakes
- 7000 lbs
- 8 on 6-1/2 Inch
- 78-1/4 Inch Long
- 94 Inch Long
- Drop - 4 Inch
- etrailer
more information >
Continue Researching
- Shop: Kenda 165/65-8 Bias Trailer Tire with 8" White Wheel - 4 on 4 - Load Range C
- Article: Trailer Wiring Diagrams
- Video: Review of Kenda Tires and Wheels - Tire with Wheel - AM3H200
- Shop: Optronics Streamline LED Trailer Tail Light - Submersible - 3 Function - 11 Diodes - Red Lens
- Shop: Kenda 165/65-8 Bias Trailer Tire with 8" Galvanized Wheel w/ Offset - 5 on 4-1/2 - Load Range C
- Shop: Kenda 215/60-8 Bias Trailer Tire with 8" Galvanized Wheel - 4 on 4 - Load Range C
- Shop: Kenda 165/65-8 Bias Trailer Tire with 8" White Wheel - 5 on 4-1/2 - Load Range C
- Shop: 7-Way Molded Connector w/ 10' Cable - Trailer End
- Shop: 7-Way Molded Trailer End with 6' Cable - HD Blue Insulated
- Q&A: Do Electric Brakes Need to Share Ground Wire?
- Q&A: Troubleshooting Voltage Drop to Trailer Brake Assemblies
- Q&A: Does the Power Wire for a Brake Controller Need to Be Ran Directly to the Battery
- Q&A: How to Hard Wire Prodigy P2 Trailer Brake Controller
- Q&A: Is 14 Gauge Wire Too Small for Electric Trailer Brakes
- Q&A: Replacing Tandem Torsion Axles On a Bison Living Quarters Horse Trailer
- Search Results: led trailer light bar
- Q&A: Prodigy Brake Controller Draining Truck Battery Overnight
- Search Results: bulldog 12000
- Search Results: bulldog square jack
- Search Results: 7k brake
- Search Results: 7k drums
- Video: Dexter 12 Inch Electric Trailer Brake Installation
- Video: Review of Dexter Axle Trailer Axles - Leaf Spring Suspension - 8327872-EB
- Video: Draw-Tite Electric Trailer Brake Controller Wiring Kit Review
- Search Results: autowbrake
- Shop: Brake Controller
- Video: Timbren Axle-Less Trailer Suspension System Test Course
- Video: Review of Kenda Trailer Tires and Wheels - Tire Only - AM10295
- Search Results: 7 blade trailer connector
- Shop: Fifth Wheel Hitch