Draw-Tite Trailer Hitch Receivers Confirmed to Fit a 2023 Hyundai Kona Electric

Question

Question:

will this hitch fit Hyundai Kona electric SE 2023 model?

asked by: Yuri

0

Expert Reply:

Yes, per Draw-Tite their Max-Frame Trailer Hitch Receiver # DT52GR will fit your 2023 Hyundai Kona SE electric. The 2" receiver will allow for a larger selection of hitch mounted accessories.

expert reply by: Bud M

0

Answer 1

I checked with Curt and their trailer wiring harness part #C99KR is a confirmed fit for the 2023 Hyundai Kona ev as it is a fit for all models.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Draw-Tite Trailer Hitch Receivers Confirmed to Fit a 2023 Hyundai Kona Electric

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching