Solera Slide Out Awning Roller Tube Inner Diameter

Question

Question:

I have an AandE 8500 Dometic awning and in attempting to replace the fabric something went radically wrong with the tension spring attached pic and I can not remove it so I am faced with replacing the roll bar and the right spring picture the left spring should beinch fine to move over to new roll bar. The solera tube seems to be configured the same as the AandE with three groves - is the inside diameter the same ? Can I accomplish my plan using the Solera tube ?

asked by: Tom C

0

Expert Reply:

The inner diameter of Solera roller tubes like the Replacement 20' Roller Tube for Solera RV Awnings # LC33FR is 3", that being said Solera and other branded awnings are not compatible with each other. We typically have a lot of people wanting to replace they Dometic awnings with the Solera replacements we carry but the arms connect differently making it a complete replacement.

expert reply by: Kevin C

0

Answer 1

We do offer a hinge that may work well for you. I recommend part #PLR1904-Z. This is a barn door hinge for dump trucks and is made of 1/4 inch steel. This has a smooth surface that is designed for welding. I have also attached a photo of this hinge…

view full answer...

Answer 2

The Solera Classic Universal Awning Support Arms #LC434720 is designed to replace the arms and springs on your manual Dometic awning. You must have between 81"-96" in height between the top awning rail and where the bottom bracket…

view full answer...

Answer 3

I took a look at what we have, and the closest I was able to find was the: - Solera Destination Manual RV Awning #LCV000335270-334719 for black. Or -Solera Destination Manual RV Awning #LCV000335296-334718 for white. These awnings measure…

view full answer...

Answer 4

The distance between the left and right support arm brackets for the Solera Smart Arm 12V Power RV Awning part #LC405523 is exactly 20' on center. I have attached a photo for you that shows how the awning width is measured. The actual fabric is…

view full answer...

Answer 5

To convert your Dometic manual awning to a power unit, you can use the Solera 12V Conversion Kit in Black #LC434723 or White #LC434724 if you have a manual crank system. These Solera kits are compatible with Dometic (A&E) awnings like what you…

view full answer...

Answer 6

Since you said you can use a Solera awning tube and yours is 19 foot 6 inches long the correct replacement roller would be the part #LC33FR.

view full answer...

Answer 7

The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…

view full answer...

Answer 8

The #LC266149 is designed to work with Solera awnings that were manufactured before 2014, where the #LC373566 is designed for awnings built after 2015. Yes, the main noticeable difference is going to be the plug, but that directly effects how it is…

view full answer...

Answer 9

Yes, the Solera Power Awning Replacement Motor #LC266149 will still work, it will just operate at a slower pace than your 100 RPM motor.

view full answer...

Answer 10

The Replacement Motor for Lippert Solera Power Awnings #LC373566 works with awnings with a range of sizes including up to 20 ft. so size is not an issue. This motor will work for you if you are replacing the motor on a Solera power awning…

view full answer...

Answer 11

The roller tube for the Solera 12' Black Fade RV Awning Roller and Fabric #LCV000211455 referenced in your question has an outside diameter of 3-1/2 inches just like what you currently have. This should work perfectly as a replacement.

view full answer...

Solera Slide Out Awning Roller Tube Inner Diameter

Product Page this Question was Asked From

Continue Researching