Does The B&W Biker Bar Require Two Anchors For Installation

Question

Question:

I am ordering the Biker Bar today. I want to have extra plates to be able to use multiple trailers, Toyhauler, etc. Does the bar use two plates per location or will two plates plus the purchase of the bar give me the option to mount to 3 different locations aka… one mounting bracket per mounting location?

asked by: Mark B

1

Helpful Expert Reply:

Each model of the B&W Biker Bar Motorcycle Tie-Down System for Trailers will use two anchor plates # BWMC2305 to connect to. The anchors would be secured to the underbelly of the trailer making it hard to use in multiple locations, so you'd really need to buy a set for each trailer you plan to haul with. The base bolts down to the anchors so if you really wanted to you can remove it from the anchors but this would also be somewhat of a hassle.

expert reply by: Kevin C

1

Answer 1

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The brake controller port on a 2021 Ford F-150 (if equipped) will be located behind the coin tray in the center console. This will be accessed by removing the panel under the steering wheel. I have attached a video which shows this below. For a brake…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

The factory hitch that came with your GMC Sierra 1500 was at least a Class III and possibly a class IV depending on what trim level you have. Looking at the available products as well as your specific application and towing needs, I recommend…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

The brackets on the SumoSprings Trailer Helper Springs #SS26MV are 1-1/2" wide so they will fit evenly across the humps on your spring pads. I do not recommend cutting down the spring and you will be able to use these even with only having…

view full answer...

Does The B&W Biker Bar Require Two Anchors For Installation

Product Page this Question was Asked From

Continue Researching