Installing Curt Front Mount Hitch # C31074 On A 2022 Chevy Colorado Z71
Question:
Does the air dam need to be trimmed or cut for the 2inch front hitch to be mounted to my truck? Does the skid plate need to be removed as well?
asked by: William J
Helpful Expert Reply:
When installing The Curt Front Mount Trailer Hitch Receiver # C31074 onto your 2022 Chevy Colorado Z71 per the instructions you will need to determine if trimming is required on vehicle by raising hitch into position. If needed, mark and trim lower fascia, as shown below or remove lower fascia and return to owner. Make sure to check for proper fit prior to trimming. You will then have to remove the skid plate and is optional to trim a 1/2 inch from edge and replace later see picture below.
The front mount hitch has an easy, bolt-on installation with no welding required. It has a gloss black powder coated finish that is over the steel that helps it resist corrosion. The hitch has a line pull up to 9,000 pounds and has a vertical load up to 500 pounds. I would recommend checking your vehicle's manual to find the proper weight capacity of your vehicle.
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Front Receiver Hitch
- Custom Fit Hitch
- Front Mount Hitch
- 500 lbs Vert Load
- 9000 lbs Line Pull
- 2 Inch Hitch
- Square Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Front Mount Hitch
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Trailer Hitch
- Shop: Roof Rack
- Shop: Grille Guard
- Shop: Bumpers
- Video: Curt Front Mount Trailer Hitch Receiver Installation - 2020 Chevrolet Colorado
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Shop: Brake Controller
- Search Results: 25580
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Article: Trailer Wiring Diagrams
- Video: EcoHitch Hidden Front Mount Trailer Hitch Installation - 2021 Ford F-250 Super Duty
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: 68149
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Lippert Solera Slider Slide-Topper Installation - 2021 Grand Design Reflection Fifth Wheel LCV000165
- Search Results: dust cap
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Video: etrailer Hitch Pin Alignment Collar Review
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Article: My Trailer Hitch Doesn't Fit
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
on Front Receiver Hitch
