B and W Gooseneck Hitch that Fits 2023 Chevy Silverado 2500 Short Bed

Question

Question:

Does the BandW BWGNRK1020 fit a 2023 Chevy Silverado 2500HD? Thanks

asked by: Roger W

0

Expert Reply:

Yes, the B and W Turnoverball gooseneck hitch part # BWGNRK1020 that you referenced does fit your 2023 Chevy Silverado 2500HD short bed as it is a carry over from the 2022 model.

expert reply by: Jameson C

0

Answer 1

The 4" hole for the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1020 will be located directly above the axle on your 2022 Chevrolet Silverado 2500. Since you have the long bed, you will measure 45-5/16" from the…

view full answer...

Answer 2

I'm not 100% sure which Curt gooseneck is on there and they use a template so I don't have the measurements handy. However, the #BWGNRK1020 does list the measurements so you can run a tape measure in your truck bed to see if it lines…

view full answer...

Answer 3

To add a B&W gooseneck hitch to your 2024 GMC Sierra 2500 you will want the Turnoverball Underbed Gooseneck Hitch item #BWGNRK1020. This hitch is custom fit and includes all hardware necessary to complete installation on your truck. It has a…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

Hi Mark; thanks for the question and I have some good news for you as we have the exact 5th wheel to gooseneck adapter to replace the Turning Point pin box on your Jayco Eagle HT 30.5 CKTS. The correct part is the following: - Gen-Y Hitch Shock…

view full answer...

Answer 9

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 11

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 12

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...