Dimensions Of The CE Smith Bow Roller Assembly # CE29335

Question

Question:

Is the 4” roller 4” or smaller

asked by: Carl

0

Expert Reply:

The CE Smith Bow Roller Assembly # CE29335 is 4 inches wide and with the bells it is 8 inches long and has a 5-1/4 inch diameter. The roller has a 1/2 inch shaft diameter.

The roller has a polyvinyl chloride (PVC) construction which is durable, non-marring, and corrosion resistant.

I attached a review video link below.

expert reply by: Noah E

0

Roller Dimensions
(click to enlarge)

Answer 1

The max rating of your Shelby 5408B is 1,900 lbs which would be more than adequate for a 2,200 lb boat as typically the ratio for winch capacity to boat weight is 2 to 1. For a similarly rated winch we have the part #DL14627 which is rated for 1,800…

view full answer...

Answer 2

The Fulton T1401 model has been discontinued. As a replacement I recommend the Fulton Single Speed Trailer Winch - 8" Long Handle - 1,500 lbs #F142201. The slightly smaller option is the Fulton Single Speed Winch - 8" Long Handle - 1,300…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 11

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 12

The Kodiak Oil Cap #KPCAP you are looking at is a replacement cap for the Kodiak Pro Lube Kit. The oil cap you need is the Redline Oil Cap, Plug and O-Ring for Dexter 7-9K Trailer Axles #RG04-230. This will replace the oil cap on your trailer axles…

view full answer...

Dimensions Of The CE Smith Bow Roller Assembly # CE29335

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching