Can Timbren Kit Install at Same Time as RAS Kit

Question

Question:

Will these work in conjunction with the Roadmaster Active Suspension?

asked by: Greg C

0

Expert Reply:

The Timbren Rear Suspension Enhancement System # TGMRCK15S would technically fit with a RAS kit installed on a truck but I would worry about whether or not you are exceeding the weight capacity of the truck if you need two suspension enhancement kits on it.

expert reply by: Jameson C

0

Answer 1

The RAS system #RAS3611-SLHD sits on your 2014 Ford F-250's leaf springs and wouldn't interfere with the Timbrens that you currently have installed. It will most likely be a bit of a pain get the RAS in place because the Timbrens sit close to…

view full answer...

Answer 2

The Curt A16 fifth wheel hitch part #C16120 that you referenced is a really nice fifth wheel hitch that would work well for you and when not in use it can easily be removed from the truck bed.

view full answer...

Answer 3

So just to answer the first part of the question, since you don't have a lift on your 2020 Chevy Silverado 1500 you do not need a spacer to use the Timbren Rear Suspension Enhancement System #TGMRCK15S. As for comparing the Timbrens to the…

view full answer...

Answer 4

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Can Timbren Kit Install at Same Time as RAS Kit

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching