Trailer Hitch And Complete Towing Setup For A 2023 Kia Sorento

Question

Question:

want to buy this hitch, but I want to make sure it will fit my 2023 kia sorento

asked by: Roman

0

Expert Reply:

Yes, the etrailer Trailer Hitch Receiver # e28AR will fit your 2023 Kia Sorento!

This trailer hitch has a maximum towing capacity of 3,500-lbs, a maximum tongue weight capacity of 525-lbs, and features an easy bolt-on installation.

expert reply by: Bryce D

0

Answer 1

For towing with your 2023 Kia Sorento you will need a trailer hitch, wiring, and a ball mount. I recommend the following: - etrailer Trailer Hitch Receiver #e28AR -T-One Vehicle Wiring Harness #118269 (If you have the factory tow package) -Curt…

view full answer...

Answer 2

For your 2021 Kia Sorento SX without the factory tow package you will need the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #TK26FR which is confirmed to fit all models of the Sorento including your SX model. At this time…

view full answer...

Answer 3

If your 2020 Kia Sorento has the factory tow package, there will be a tail light wiring connector behind the rear tire of the driver side, on the outside of the frame rail. As shown in the attached photos, an underbody cover will need to be removed…

view full answer...

Answer 4

We do have a hitch that is confirmed to fit your 2023 Kia Sorento, the etrailer Trailer Hitch #e28AR. For wiring, I recommend the Curt T-Connector Vehicle Wiring Harness #C99DR. This plugs in behind your tail lights so no cutting or splicing is…

view full answer...

Answer 5

Yes, the Curt trailer wiring harness part #C99DR that you referenced does fit our 2023 Kia Sportage PHEV model as we have confirmed this with Curt.

view full answer...

Answer 6

Yes we have the Draw Tite hitch part #C34ER that is a confirmed fit for your 2023 Kia Sorento. It has great towing capacities at 3,500 lb trailer weight and 525 lb tongue weight as well as an easier install. Then for trailer wiring the Curt kit part…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Trailer Hitch And Complete Towing Setup For A 2023 Kia Sorento

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching