Drill Tap Size for Installing Curt Hitch on 2011 Honda CR-V

Question

Question:

10 x 1.25 mm or 10 x 1.50 mm? I have two metric taps which are the same diameter, but different thread count. Which is needed for the #13555 Curt hitch - 2011 Honda CR-V?

asked by: David D

0

Expert Reply:

The tap you want to use for installing the Curt Trailer Hitch Receiver # 13555 on your 2011 Honda CR-V is 10x1.25mm as the bolts that come with the hitch are M10x1.25.

Attached is an installation video of this hitch on a 2011 CR-V for you to check out. If you let me know what you plan on using the hitch for I'd be more than happy to make a recommendation for you!

expert reply by: Jon G

0

Answer 1

The mounting bolts that attach the hitch into the nuts welded into the frame members should be 10mm. I can make a pretty good guess about what you have going on. Vehicles that are more than a couple of years old can get road grunge and corrosion…

view full answer...

Answer 2

The bolts that come with the Curt Trailer Hitch #13555 on your 2008 Honda CR-V are M10 - 1.25 x 30 hex bolts. We actually have replacement hardware available as part #RHK on our site. Simply go to the product page and then select the manufacturer…

view full answer...

Answer 3

If you torque the install hardware of the Curt hitch part #13555 properly you would not need any Loc-Tite. The install hardware is torque-to-yield which means that the bolts act as their own thread lock as they stretch to keep themselves from backing…

view full answer...

Answer 4

The u-bolt included in the hardware for hitch #13555 is a 7/16 - 14 x 1.75" x 1.00" C-C u-bolt. We do not offer this item alone but you can probably find one locally using those specs. We do offer the complete replacement hardware kit for…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Drill Tap Size for Installing Curt Hitch on 2011 Honda CR-V

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching