Does The Ramp Door Hinge # PLR1902 Have a Solid Hinge Pin?

Question

Question:

Is the pin on this hinge solid all the way thru?

asked by: KD

0

Expert Reply:

Yes, the Ramp Door Hinge # PLR1902 has a solid 1/2" steel internal pin that passes all the way thru the hinge.

expert reply by: Bud M

0

Answer 1

The Ramp Door Hinge #PLR1902 isn't tested for a specific weight capacity. However, it is intended to be used on heavy trailer doors.

view full answer...

Answer 2

The piano style hinges such as #SH200 are fairly stout but what I recommend is a combination of a piano hinge and regular ramp door hinges such as #PLR1902. Since you will be putting a considerable amount of weight on the ramp you want everything to…

view full answer...

Answer 3

The Ramp Door Hinge #PLR1902 that you referenced does not come with 2 of the plates for welding. You will weld the plate to one surface and the outside ends of the pin to the other for installation. For a hinge that has 2 of the plates you would want…

view full answer...

Answer 4

The Ramp Door Hinge #PLR1902 does require welding of both portions. The tab gets welded as you stated to one side and the outside cylinders get welded to the opposite side. I've attached a couple pictures to assist.

view full answer...

Answer 5

If your trailer is brand new and recently purchased ideally you would return to the dealer to have the ramp corrected. The amount of misalignment you describe seems excessive for a brand new trailer. If the trailer is parked on uneven ground the ramp…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 10

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 11

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 12

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Does The Ramp Door Hinge # PLR1902 Have a Solid Hinge Pin?

Product Page this Question was Asked From

Continue Researching