What is Weight of BedSlide Sliding Truck Bed Tray w/ T-Tracks BE23ER

Question

Question:

How much does this item weigh?

asked by: Alan D

0

Expert Reply:

The BedSlide Sliding Truck Bed Tray w/ T-Tracks # BE23ER that you referenced weighs 124 lbs.

expert reply by: Jameson C

0

Answer 1

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 2

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 3

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 6

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 7

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 8

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 9

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

What is Weight of BedSlide Sliding Truck Bed Tray w/ T-Tracks BE23ER

Product Page this Question was Asked From

Continue Researching