How to Wire Up a Breakaway Battery and an Auxiliary Battery on a Trailer without Backfeeding
Question:
Just installed. Trailer is in garage hooked to nothing. When I attached ground wire the yellow charging light went on. I waited one hour hoping it would go off but it hasnt. My question to you is this Since this is a tilt trailer with a battery electric powers hydraulics will this light stay on all the time? If so, how do I make it so this doesnt stay on without disconnecting ground each time I unhook trailer Thanks
asked by: Donnie
Expert Reply:
It sounds like the tilt battery is backfeeding onto the breakaway battery charge line so as long as the ground is connecting it is taking a charge from the tilt battery and that is why your charge light is staying on.
I have a solution for you, you will need a single function diode part # RM-690. You will need to wire it in between the breakaway battery and the tilt battery and it will stop the backfeeding from your tilt battery to the rest of the 12 volt circuit wiring of your trailer.
Check out the diagram I put together to show you how it should all get wired up.
Products Referenced in This Question
Roadmaster Single Park Light Diode
- Accessories and Parts
- Tow Bar Wiring
- Diodes
- Roadmaster
more information >
Product Page this Question was Asked From
Hopkins Engager Push-To-Test Trailer Breakaway Kit w/ Built-In Charger - Side Load - 7" Wire
- Trailer Breakaway Kit
- Kit with Charger
- Side Load
- Single-axle
- Tandem-axle
- LED Tester
- Hopkins
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Optronics LED Trailer License Plate Light w/ Bracket - 5 Diodes - Clear Lens
- Search Results: e32jr
- Search Results: 12~706
- Search Results: safety chains
- Search Results: 126003
- Search Results: saftey chains
- Search Results: 122096
- Search Results: 3375601101
- Shop: Dexter Trailer Hub and Drum Assembly - 7K lb E-Z Lube Axle - 12" - 8 on 6-1/2 - 5/8" Studs
- Shop: Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End
- Shop: Laclede 35" Long Trailer Safety Chain w/ Clevis Slip Hook - 5,400 lbs Weight Capacity - Qty 1
- Shop: Dexter Electric Trailer Brake Assembly - 10" - Left Hand - 3,500 lbs
- Shop: Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased
- Shop: Dexter Electric Trailer Brake Assembly - 10" - Right Hand - 3,500 lbs
- Article: Trailer Wiring Diagrams
- Q&A: Wiring Diagram for Trailer Breakaway Kit
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Q&A: Is a Diode Needed to Prevent Backfeeding from Trailer to Tow Vehicle
- Q&A: Can a Diode be Used to Prevent Back Feeding from a Trailer Breakaway Battery to a Brake Controller
- Article: Diode Installation Instructions for a Dinghy with Separate Tail Light Wiring
- Shop: Vehicle Tow Bar Wiring
- Q&A: Wiring Trailer for Two Batteries, Breakaway Battery and Auxiliary Battery
- Q&A: How to Wire a Trailer Break Away System and Connect Auxillary Battery and Brake Wires
- Q&A: How to Wire 12V Battery in Enclosed Trailer to Power Trailer Lights Independent of 7-Way Connection
- Video: Spectro Trailer Wiring Junction Box Installation
- Q&A: Adding a Battery on an Enclosed Trailer to Power Interior Lights
- Shop: Trailer Wiring
- Video: Review of Roadmaster Tow Bar Wiring - Single Park Light Diode - RM-690
- Shop: RV Interior Lighting
- Shop: Brake Controller