Trailer Axle Solution for 60" Hub Face and 46-1/2" Spring Center Measurements
Question:
I am trying to find out about a axle for my jet ski trailer, spring mounts are 46 1/2 to center and 60 in to hub face.
asked by: Zack
Expert Reply:
I have some possible solutions for your application, but the Trailer Axle with Idler Hubs # e25GR that you were looking at has the 60" long hub face length you're needing but the spring center distance is 48" which is a bit longer than what you're needing and unfortunately the only spring center length we have for the 60" axles.
To get this to fit your jet ski trailer you'll have to have a welder cut off the current spring seats and weld on new ones with part # TRSS175. For a standard axle replacement with the same dimensions you'll need to reach out to your local RV or trailer shop to custom order one for you.
An alternative would be to go with the Timbren Axle-Less Trailer Suspension System with Hubs # A20RS440 instead. These use a different type of suspension with individual Aeon springs. This gives your trailer better performance and these are easier to maintain over the standard leaf spring setup but it does mean you'll be redoing the whole trailer axle system on your trailer instead of just bolting a new axle up.
Attached is a video of the Timbren kit for you to check out.
Products Referenced in This Question
Timbren Axle-Less Trailer Suspension w/ Idler Hubs - Standard Duty - No Drop - 4 on 4 - 2,000 lbs
- Trailer Axles
- Rubber Spring Suspension
- Easy Lube Spindles
- Idler Hubs
- 2000 lbs
- 4 on 4 Inch
- Universal Fit
- No Drop or Lift
- Timbren
more information >
Spring Seat for Typical 2,000-lb, Round Trailer Axles with 1-3/4" Diameter - Qty 1
- Trailer Suspension Parts
- Spring Seats
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Round Axle - 1-3/4 Inch
- TruRyde
more information >
Product Page this Question was Asked From
Trailer Axle with Idler Hubs - 4 on 4 Bolt Pattern - 60" Long - 2,000 lbs
- Trailer Axles
- Leaf Spring Suspension
- Easy Lube Spindles
- Idler Hubs
- 2000 lbs
- 4 on 4 Inch
- 48 Inch Long
- 60 Inch Long
- No Drop or Lift
- etrailer
more information >
Continue Researching
- Search Results: hub and spindle
- Search Results: ah15450ecomp
- Search Results: e82gr
- Search Results: trailer drop axle
- Search Results: drop down axle
- Shop: CE Smith Trailer Axle Beam with Standard Spindles - Galvanized - 57-1/2" Long - 1.8K
- Shop: Trailer Hub Assembly - 3,000 lbs Axles - 4 on 5 - Agricultural
- Shop: Agricultural Spindle for 3,000-lb Trailer Axles - 1-5/8" Diameter
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5-1/2 - Pre-Greased
- Shop: CE Smith Trailer Axle w/ Idler Hubs - 5 on 4-1/2 - 57-1/2" Long - 1.8K
- Shop: BTR E-Z Lube Spindle w/ Brake Flange for 2,500-lb Trailer Axles - 1-3/4" Diameter
- Shop: #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter
- Q&A: What Size Axle Tube Is Needed for the #84 E-Z Lube Spindle
- Q&A: Troubleshooting Install of Curt Breakaway Kit on Trailer Where Brake Lock Up
- Search Results: drop jack
- Search Results: drop leg stabilizer
- Q&A: Trailer Hub Recommendation with Bearings LM11949 and LM67048
- Q&A: Recommended Replacement Trailer Hub Assembly for Custom Boat Trailer
- Q&A: Replacement Axle Spindle With 2.25 Diameter Spindle
- Q&A: Agricultural Hub Availability
- Q&A: Hub For Outer Bearing LM11949 & Inner Bearing LM67048
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-440-2-G-EZ-1K Review
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-440-2-G-1K Review
- Video: etrailer Trailer Idler Hub Assembly Review and Installation
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Video: etrailer Trailer Bearings Races Seals Caps - Bearings - LM67048 Review
- Video: Dexter Axle Trailer Axles - Leaf Spring Suspension - 20440I-ST-60 Review