Comparing Curt 13390 and 13206 Trailer Hitches for a 2017 Subaru Outback Wagon

Question

Question:

Might I ask what the difference in dimensions are, both years share the same chassis

asked by: William Q

1

Helpful Expert Reply:

The difference between the Curt # 13390 and # C13206 hitches is that the 13206 sits up closer to the bumper by about 1/4" and the receiver sits out further to the back of the vehicle by about 1/8" - aside from that the dimensions are the same.

Curt made this redesign and just started listing the 13206 for the Subaru Outback Wagons starting with the 2014-2015 model year. Since Curt recommends the 13206 for your 2017 Subaru Outback Wagon that's what I recommend going with as well.

Attached is an installation video of this hitch on a 2017 Outback Wagon for you to check out. If you let me know what you plan on using the hitch for I'd be more than happy to make some recommendations for you!

expert reply by: Jon G

1

Grant

5/16/2024

I accidentally ordered the 13390, would this still be installable on my 2017 Outback? Many thanks!

Reply

Jon G.

5/16/2024

@Grant The bolt pattern on the Curt Trailer Hitch Receiver # 13390 will match the pattern on your 2017 Subaru Outback, but I don't have any insight into how well it will fit with the rear fascia. You should be able to maneuver it into place without installing it so I recommend carefully unboxing the hitch and holding it up in place prior to unwrapping all of the hardware and such. If the mock-up matches up well then you'll be good to go since the hardware is the exact same for the hitches. If the mock-up doesn't match, then you'll want to return it for the # C13206.

Reply

Answer 1

The difference is what vehicles each of those hitches will fit. Trailer hitch #C13206 fits 2014 to 2016 Subaru Outbacks. And #13390 fits the 2015 to 2016 Legacy and 2010 to 2013 Outback. Although the hitches look very similar for your 2015 Outback…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 9

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 12

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Comparing Curt 13390 and 13206 Trailer Hitches for a 2017 Subaru Outback Wagon

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching