Replacement Pin For Swing Away Tongue On a Tracker Boat Trailer

Question

Question:

What size pin for tracker boat trailer with swing tongue

asked by: Jim S

1

Helpful Expert Reply:

A 5/8" pin is the most common diameter used for a swing away tongue. There are different length pins for different height frames. The only one we currently carry is for a 5" tall frame, for this you will use a Pin # F500336. Be sure to verify both the height and diameter for your specific coupler as they can be different between model years and model trailers.

expert reply by: Bud M

1

Answer 1

A spacer or hub-centric ring is sometimes used on passenger vehicles, but our resident wheel and tire guru tells me that they aren't needed for use on trailers, due to the weight load a trailer wheel will be under. If you feel you need them, you…

view full answer...

Answer 2

Yes, it is certainly possible to remove the pivot bolt from the Fulton Fold-Away Coupler Hinge Kit #FHDPW330300 to enable you to separate the two halves of the assembly. Both the pivot pin and pivot bolt are included with this assembly and it is…

view full answer...

Answer 3

We were able to find out the dimensions for you of the Fulton Fold-Away Coupler Hinge Rubber Plug Kit #F500705. Using digital calipers it measured 0.423 inches tall and its round base has a diameter that measured 0.426". These are designed to…

view full answer...

Answer 4

The Replacement Pivot Pin part #F500336 is not rated like a bolt grade. As long as the hinge kit you use is rated for the weight of the trailer, you'd be fine.

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Replacement Pin For Swing Away Tongue On a Tracker Boat Trailer

Product Page this Question was Asked From

Continue Researching