Recommended Replacement Entry Door Hinge For With A 6-Leaf Configuration

Question

Question:

The top and bottom hinge are the same I will be sending pictures. Need this same one

asked by: Alfonso

0

Expert Reply:

While we don't carry a hinge with the exact leaf setup as what you have pictured, the Replacement Controlled Motion Hinge for RV Entry Door - 6 Leaf - Black # LC95VR is still a viable replacement option. Since the leaf configuration is slightly different you will have to drill new holes for mounting.

expert reply by: Kevin C

0

Customer Hinge
(click to enlarge)

Answer 1

Although we do not have the instructions for the Replacement Controlled Motion Hinge for RV Entry Door #LC95VR that you mention I was able to get in contact with Lippert, and they were able to send over the instructions. The instructions are as…

view full answer...

Answer 2

The only black replacement hinge option we carry is the Replacement Controlled Motion Hinge for RV Entry Door - 6 Leaf - Black #LC95VR. This hinge will work as a replacement but you'll notice the mounting holes most likely won't match up so…

view full answer...

Answer 3

No the Replacement Controlled Motion Hinge for RV Entry Door - 6 Leaf - Black #LC95VR does not come with mounting hardware. You will need to reuse the existing hardware.

view full answer...

Answer 4

If the door hinge on your 2005 Winnebago Vectra has a similar design then yes, the Replacement Controlled Motion Hinge for RV Entry Door - 6 Leaf #LC95VR will work as a replacement. This is a universal product that has an overall length of…

view full answer...

Answer 5

The Lippert #LC95VR Controlled Motion Door Hinge will fit most doors. To check for size, compare your door thickness with the provided dimensions on the attached drawing. The leafs with 3 holes go on the outer wall frame. Leafs number 2 and number 4…

view full answer...

Answer 6

The typical tire should run about 158 degrees (Farenheidt) once you get going down the road, but this can vary greatly depending on the weight of the trailer, how fast you're traveling, and also driving habits. So while 158 is probably…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Recommended Replacement Entry Door Hinge For With A 6-Leaf Configuration

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching