Weight Rating of the Gen-Y Iron Grip Anti-Rattle Hitch Pin for 3" Hitch Receivers

Question

Question:

Does the Gen-Y Iron Grip Anti-Rattle Hitch Pin for 3inch Hitch Receivers - 5/8inch Diameter have a weight rating?

asked by: Jason S

1

Helpful Expert Reply:

I just checked with Gen-Y. The Gen-Y Iron Grip Anti-Rattle Hitch Pin for 3" Hitch Receivers - 5/8" Diameter item # GY49FR is rated for 21,000 lbs.

expert reply by: Jerred H

1

Answer 1

I checked with Gen Y and they told me that the length of the Replacement Hitch Pin Clips part #GY69FR is 2-3/4 inch and the diameter is 1/8 inch.

view full answer...

Answer 2

The Gen-Y Iron Grip Anti-Rattle Hitch Pin for 2" Hitch Receivers #GY39FR is rated for 21,000lbs. So you will have no issues using this with your receiver.

view full answer...

Answer 3

Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…

view full answer...

Answer 4

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 5

I confirmed with my contacts at Gen-Y Hitch that Gen-Y Hitch Pin #325-GH-099 tow rating is 32000 lb (shear strength) without the reducer sleeve. This hitch pin is designed for use with 2" by 2" and 2-1/2" by 2-1/2" hitches.

view full answer...

Answer 6

We aren't manufacturers of those parts, and we don't have the testing ability in house, so I reached out to a couple of our manufacturers to see what information they could provide to try and help. I reached out to my contact at Curt…

view full answer...

Answer 7

You made a great choice in the Lippert Components Power Stabilizer Trailer Jack. For starters, all of the jacks measure to be 70-1/2" long with a 3,500 lb weight capacity and have a 30" lift. The difference between them is in regards to…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Weight Rating of the Gen-Y Iron Grip Anti-Rattle Hitch Pin for 3" Hitch Receivers

Product Page this Question was Asked From

Continue Researching