How Do Carr # CARR103991 Hoop Steps Attach to 2003 Ram Quad Cab

Question

Question:

I have a 2003 Ram quad cab. How do the steps mount to the vehicle.

asked by: Carl M

0

Expert Reply:

The Carr # CARR103991 hoop steps are a confirmed fit for your vehicle. For both the front and rear doors, you'll need two sets of steps. The steps attach to the vehicle by bolts that run through the body pinch weld and screws into the rocker panel, as shown in the instructions I've linked you to.

The attachment is extremely sturdy. A co-worker of mine has these installed on his truck, and they don't budge or flex the tiniest bit when they're stepped on.

expert reply by: Mike L

0

click to enlarge

Answer 1

I went out to our warehouse and measured the: -Replacement Mounting Brackets for Carr Custom-Fit Side Step #CARRBR14702K2, and was able to get the following dimensions for you: -Overall Height - 3-7/8", -Bracket Height At Bend - 3-1/4",…

view full answer...

Answer 2

The Bully Black Bull Side Steps - Aluminum - Matte Black - 7" Step - 1 Pair #BBS-1103 is 7 inches long x 3-5/8 inches wide. The height from your pinch weld on your vehicle to the top of the step will depend on how you mount the step but you can…

view full answer...

Answer 3

The distance between the two mounting holes on the mounting bracket for the part #CARR103991-1 is 1.9 inches.

view full answer...

Answer 4

The Carr Custom-Fit Side Steps - Hoop II - Black Powder Coated Aluminum - 7" Step - 1 Pair #CARR103991 have a measurement of 1.9 inches vertically and 8.5 inches horizontally measuring hole center on center. I've attached a photo to assist.

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

How Do Carr # CARR103991 Hoop Steps Attach to 2003 Ram Quad Cab

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching