Installation of a Prodigy P2 # 90885 Proportional Brake Controller on a 2012 Chevy Suburban
Question:
wiring hookup to 2012 suburban for 90885-22292 brake controller?
asked by: Roger S
Expert Reply:
To install the Tekonsha Prodigy P2 proportional brake controller # 90885 you will not need the additional wiring harness # 22292. The # 22292 is a plug in adapter that is designed for use with Ford F-150 trucks, and you will not need this portion for installation on your 2013 Chevrolet Suburban. You will only need the wiring that is included with the Brake controller and hard wire that to your vehicles existing wiring.
On your 2012 Chevrolet Suburban there is not a plug that is present under the dash but the necessary wires are there to install the brake controller. On your vehicle wiring that is located under the dash and above the brake pedal you will need to identify the following wires: the 12V vehicle power (red with black stripe), the outgoing brake signal (blue), the ground (white) and brake signal from vehicle (blue with white stripe).
Once you have identified these wires on your vehicle you can then proceed to install the brake controller as follows: Vehicle 12V will connect to the black wire on the brake contoller, the brake output for the trailer will connect to the blue wire on the brake controller, the ground on the vehicle will connect to the ground on the brake controller, and the brake signal from the vehicle will connect to the blue wire on the brake controller.
After the wiring connections are made with the factory installed brake wiring you can install the brake controller mounting bracket in your desired location and connect the brake controller to the plug that you just wired from your vehicle wiring and install the brake controller in the bracket.
Power will still need to be run to the brake controller and this is also included with your vehicle wiring. This is located under the hood near the fuse box and battery location. You will have to connect the wire labeled 12V aftermarket trailer feed and connect this to the positive side of the battery. After installing the brake controller, I recommend using a circuit tester like part # PTW2993 and verifying the functions and the connections before towing.
I have included links to the parts listed above, a video of an install of this brake controller on a very similar vehicle, and a helpful article for your reference.
Products Referenced in This Question
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: How To Add a Fuel Tank To a Truck with 5th Wheel Hitch In Bed
- Q&A: Recommended 16' Mesh Tarp for Dump Trailer
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Article: Best Camper Jacks
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Wiring Diagram for Bargman 7-Way RV Style Connector # WG54006-043
- Q&A: Replacement Trailer Jack Recommendation for Dutton-Lainson Jack on Ranger Trailer
- Q&A: Troubleshooting Kodiak 225 Trailer Brake System that Keeps Breaking Calipers In Half
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)