Attaching An OEM Camera To The Stromberg Carlson 4000 Series Louvered Tailgate

Question

Question:

The 5th wheel tailgate for a 2019 f250, can you connect oem camera to it? Thanks

asked by: John L

0

Expert Reply:

The Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate with Lock for Ford Trucks, part # VG-15-4000, is not designed to work with your OEM camera. Your best option might be to zip tie your camera to the tailgate. It is not ideal, but your camera will still be functional.

I have included a video review of the tailgate below.

expert reply by: Mark Smith

0

Answer 1

Most manufacturers are in the process of discontinuing their fifth wheel tailgates with the camera relocation kits due to mechanical issues. Therefore I could not find one that fits your 2017 Ford F-350 Super Duty. The Stromberg Carlson 4000 Series…

view full answer...

Answer 2

In regards to the Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter part #AM3200, the four kingpin coupler set screws will need to be torqued to 40 ft. lbs. per the manual. The kingpin coupler will need to be center on the pin…

view full answer...

Answer 3

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 4

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 5

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 6

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 7

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 10

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 11

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 12

Yes, you can use the NOCO GEN On-Board Battery Charger #NOC34FR on your pickup's parallel batteries without disconnecting them. If your batteries were in a series, they would have to be disconnected. Since your batteries are parallel and maintain…

view full answer...

Attaching An OEM Camera To The Stromberg Carlson 4000 Series Louvered Tailgate

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching