Is There a TorkLift Trailer Hitch for a 2005 Dodge Ram 3500 without Factory Trailer Hitch

Question

Question:

do you make a super hitch for dodge 1 ton dually ??? Truck has no reciever hitch .

asked by: Chris M

0

Expert Reply:

I do have an option for you but the only TorkLift Trailer Hitch options available for a 2005 Dodge Ram 3500 require the factory trailer hitch to be in place such as the TorkLift SuperHitch Original Trailer Hitch Receiver part # TLD1102. If this isn't an option for you I recommend the Curt Trailer Hitch Receiver part # C15809 which will bolt up to the frame without a factory trailer hitch in place.

expert reply by: Conner L

0

Answer 1

The TorkLift SuperHitch Original Trailer Hitch Receiver #TLD1108 will only fit the 2013-2018 Ram 2500 and 3500 models. Your 2007 Dodge Ram 3500 will require the TorkLift SuperHitch Magnum Trailer Hitch Receiver #TLD1102-30 or Original #TLD1102.…

view full answer...

Answer 2

For your 2018 Ram 2500 without factory hitch, the Class V hitch I recommend is the Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2" #C15409. This hitch is a fit for either 8 foot or 6-1/2 foot beds whether you have a factory hitch…

view full answer...

Answer 3

Since your factory hitch is bolted on and not welded on the correct Torklift hitch is the #TLD1102 and not the part.

view full answer...

Answer 4

Yes, the TorkLift #TLD1102 you were looking at will work with your 2006 Ram 2500 short bed 4x2 that has the bracket you show in the picture as it's designed to work with all models of your truck that came with the factory hitch.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 9

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 12

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack…

view full answer...

Is There a TorkLift Trailer Hitch for a 2005 Dodge Ram 3500 without Factory Trailer Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching