Westin Grille Guard Mounting Kit for 2004 Dodge Ram 1500

Question

Question:

I need to know the exact brackets/mounting kit for my 2004 dodge 1500 truck.

asked by: Raul E

0

Expert Reply:

We have one Westin grille guard that is confirmed to fit the 2004 Dodge Ram 1500 which is the # 40-1205. Assuming you have this grille guard the correct hardware is the Replacement Hardware Kit for Westin Sportsman Grille Guard 40-1205 # 40-120PK.

expert reply by: Robin H

0

Answer 1

Yes, the package contents for the Replacement Hardware Kit for Westin Sportsman Grille Guard #40-120PK are as pictured. This kit will work to install the Westin Sportsman Grille Guard #40-1205 that is a confirmed fit for your 2003 Dodge Ram Pickup.…

view full answer...

Answer 2

We do offer the replacement hardware kit part #40-120PK.

view full answer...

Answer 3

We do have a replacement hardware kit that fits a Westin Sportsman Grille Guard on a 2004 Dodge Ram 1500 with the part #40-120PK as it fits the 45-1200 that your truck would have.

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 8

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 9

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 12

Hello Cory. I can definitely point you in the right direction, but there is not a B&W Companion option that will fit into a round gooseneck ball hole. As you said, the B&W Companion hitch is only compatible with the B&W Turnoverball…

view full answer...

Westin Grille Guard Mounting Kit for 2004 Dodge Ram 1500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching