Installation Instructions for the Stromberg Carlson 2" Motor Home Hitch Receiver for RV Bumpers

Question

Question:

I received my order, but NO instructions were included. I watched a video, but it mentions tightening the bolts and torquing per instructions. Again no instructions. Can I get some instructions emailed

asked by: Randall R

0

Expert Reply:

I am sorry to hear your hitch arrived with no instructions. I have included a picture of the instructions for the Stromberg Carlson 2" Motor Home Hitch Receiver for RV Bumpers # BA-100.

expert reply by: Scott S

0

Stromberg Carlson BA-100 Instructions
(click to enlarge)

Answer 1

The owner's manual for a 2019 Volkswagen Atlas does say not to use a "weight distributing or load equalizing hitch" and this is strictly a Volkswagen stance. It also says things like "when you are not towing, remove the trailer…

view full answer...

Answer 2

This rack part #S80600 does require the bikes to all be a close wheel size due to the way it mounts to the bumper. I highly recommend adding a receiver tube to your bumper part #BA-100. This opens up your opportunity for hitch mounted accessories and…

view full answer...

Answer 3

I took a look at the owner's manual for your 2022 Volkswagen Atlas and it states, "Never install weight distributing or load equalizing ball mounts. The vehicle was not designed for these types of trailer hitches. The trailer hitch could…

view full answer...

Answer 4

Both the Curt #C13366 and the Draw-Tite #76176 have been designed to be mostly concealed behind the bumper once installed. The only portion of the hitch that will be visible from the rear is the receiver tube and the safety chain loops. Both hitches…

view full answer...

Answer 5

To get power to the controller of your Solera Smart Arm 12V Power RV Awning part #LC759404, you need to tap into an existing circuit, or run a power wire from the battery with an inline fuse holder, and a 15 amp fuse, like part #SWC9538, and part…

view full answer...

Answer 6

We do have awning power switches with four wires in both black and white, the Replacement Switch Kit for Solera Power RV Awnings part #LC285499 for white or part #LC285500 for black. Please note, if your wire colors don't match you will need to…

view full answer...

Answer 7

I went out to the warehouse and took several measurements of Curt Hook with Spring Loaded Safety Latch #C81840 for you. I have included a picture showing the measurements.

view full answer...

Answer 8

The Brophy Rigid Mount Spare Tire Carrier #BR56VR will allow you to carry a spare tire with Wheel #TA56FR on your 4" RV Bumper. I have included an image below of a similar setup so you can see how it fits.

view full answer...

Answer 9

From my research it looks like the correct replacement seal for your Reliable oil bath kit is the Replacement Seal #XLPROLUBE1980SEAL which is used for 3,500 lb axles. This seal has a 1.72" inner diameter and a 2.56" outside diameter. You…

view full answer...

Answer 10

I will start by saying the ARK Extreme Off-Road Ratcheting Trailer Jack w/ Wheel #ORJW1SU will fit frames that are 2" to 6" tall. The bolt hole measurements vary and I included a diagram with everything listed, but the overall dimensions of…

view full answer...

Answer 11

Bike carriers that are designed to work on the rear of an RV are made so that they can take the additional stress at the back of the RV. Yakima does not recommend using the HoldUp Rack on RVs because a bike rack mounted on the rear of a motor home…

view full answer...

Installation Instructions for the Stromberg Carlson 2" Motor Home Hitch Receiver for RV Bumpers

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching