Recommended Towing Package For A 1999 Toyota Land Cruiser
Question:
Hello. I have a 1999 Toyota Land Cruiser without the towing package. Im interested in adding the Draw-Tite hitch, Redarc Tow-Pro Elite, and a combined 4/7 pin socket. Im wondering what other parts I will need to get the job done on my Toyota. I am comfortable with wiring, drilling, etc. but would prefer as plug-and-play as possible just as a time consideration. Any suggestions would be greatly appreciated. Thanks!
asked by: Eric M
Helpful Expert Reply:
When it comes to installing a trailer hitch on your 1999 Toyota Land Cruiser The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2 inch # 75095 is confirmed for your vehicle.
The hitch has an easy, bolt-on installation with no welding required. The hitch has a black powder coat finish that covers the e-coat base for superior rust protection.
The Curt T-Connector Vehicle Wiring Harness # C55365 is an easy plug and play harness that plugs underneath the vehicle near the center. To be able to run The Redarc Tow-Pro Elite # RED44FR you will also need The Universal 7 Way Wiring Harness # ETBC7. This harness will make your 4 flat into a 7 round and a 4 flat option.
To finish off your towing experience The Curt Towing Starter Kit # C45554 will provide the ball mount, a 2 inch hitch ball and other towing accessories that will help with towing.
I attached a installation video link below.
Products Referenced in This Question
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 2 Inch Ball
- One Ball
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 2 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Redarc Tow-Pro Elite Brake Controller - Dash Knob - 2 Braking Modes - 1 to 3 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Dash-Mounted Knob
- Hidden
- Up to 3 Axles
- Indicator Lights
- Redarc
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Trailer Wiring Diagrams
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Hub And Drum Replacement for 90865 Rockwell Hub and Drum
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Brake Controller Wiring for Ford E-450 Motorhome
- Article: Trailer Maintenance Schedule
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: REDARC Tow-Pro Liberty vs Tow-Pro Elite
- Q&A: Bearings and Seal Used for AL-KO 7290 Trailer Hubs for #99 Spindles
- Q&A: Can Short Bed Trucks Tow Gooseneck Trailers
- Q&A: AxleTek Brake Assembly Recommendation for 8k Axles with 4 Bolt Mounting Pattern
- Q&A: Lippert Crank Handle for Lippert Spare Tire Winch Assembly