What is the Distance from the Hitch Pin Hole to the Weld Gusset on Brophy Ball Mount BM10

Question

Question:

What is the distance from the pin hole to the weld gussett in the drop position

asked by: Ken S

1

Helpful Expert Reply:

The Brophy 2-inch Ball Mount # BM10 measures 3-1/2 inches from the center of the hitch pin hole to the nearest edge of the gusset weld seam. The photo provided includes this measurement.

expert reply by: Adam R

1

click to enlarge

Answer 1

If you are going to change connectors the EZ Connector Magnetic 7-Way Trailer Connector #319-S7-10 would be the route I recommend going. Unlike your 7-way blade and 7-way round connectors this connector does not have any form of tension connector…

view full answer...

Answer 2

Yes. To upgrade your 600 lb Equal-i-zer weight distribution system to a higher capacity, you will need to replace your spring bars, but also the head. I recommend the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems - Qty 2 - 1,200…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

What is the Distance from the Hitch Pin Hole to the Weld Gusset on Brophy Ball Mount BM10

Product Page this Question was Asked From

Continue Researching