Correct Number of Coil SumoSprings Custom Helper Springs Needed for 2020 Toyota Highlander

Question

Question:

Rear suspension helper on a 2020 Highlander, can you put more than one css-1145 on each spring.

asked by: Mike S

0

Expert Reply:

The Coil SumoSprings Custom Helper Springs part # CSS-1145 for AWD or part # CSS-1125 for FWD will use one spacer per coil spring, you cannot use two per side nor would you want to as the ride would be too stiff but there is not enough room anyhow. These will be great for towing or hauling heavy load and they are currently the only option we have to help with rear end sag/squat.

expert reply by: Conner L

0

Answer 1

I wish I could say yes, but as of right now they are not a fit for the 2016 models and we do not have any other suspension enhancement options. If you are trying to fight suspension sag from the tongue weight of a trailer there is a better option.…

view full answer...

Answer 2

The SuperSprings Coil SumoSprings Custom Helper Springs #CSS-1145R referenced in your question is confirmed to fit your 4WD 2012 Toyota Highlander. These springs will simply insert between the individual coils of each coil spring to enhance the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

I recommend our etrailer Trailer Hitch Receiver #e75ZR as the best option for your 2024 Toyota Highlander. I feel this one is best as it has the easy bolt on installation with hidden cross-tube and a matte black finish for a clean OEM appearance. You…

view full answer...

Answer 11

First you will need the Curt T-Connector Vehicle Wiring Harness #C79VV to connect to the factory wiring on your 2024 Toyota Grand Highlander. This will take care of the lighting needed for the trailer which will connect through the 7-Way Kit #ETBC7.…

view full answer...

Answer 12

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...