Landing Gear Replacement for Keystone Laredo that Allows Reusing Motor
Question:
Can I use my factory motor that is on my camper now for this new landing gear? The motor still works fine. My landing gear acme nut threads are going bad. Last year I had to take one of the legs at a campsite, and clean up the threads of one of the acme nuts, and put it back together. Ultimately, I need new landing gear, but want to use the motor that is on it now. The camper is a 2006 Keystone Laredo 26BH. Thank you!
asked by: Andy J
Expert Reply:
If the brand of landing gear you have now on your Keystone Laredo is a Ram brand then yes you could reuse it's motor with the # RVLG-8HDL. But most likely you have a Lippert set of landing gear based on what typically they used so instead the part # LC333966 would be what you'd want instead so that you could reuse the motor.
Products Referenced in This Question
Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 5001 - 6000 lbs
- Landing Gear
- Sidewind Jack
- 37 Inch Lift
- Weld-On
- 2 Jacks
- Lippert
more information >
Product Page this Question was Asked From
Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Video: etrailer Landing Gear Set Review
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Shop: Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs
- Shop: Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
- Shop: Replacement Lifting Nut for Curt Heavy Duty Direct Weld Square Jack
- Q&A: How to Know if Landing Gear Set # RVLG-8HDL Will Fit 2001 Sunnybrook 31BWFS
- Video: Rebuilding the etrailer and Ram Square Jacks
- Shop: Replacement Follow Leg for Keystone Montana 5th Wheel Landing Gear
- Shop: Replacement Follow Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Search Results: lc142178
- Video: Review of etrailer - Trailer Jack,Camper Jack - RVLG-RDBOX
- Q&A: Will the Landing Gear part # RVLG-8HDL Fit my 2007 Keystone Laredo
- Q&A: Replacement Landing Gear for 2010 Keystone Fuzion FZ322 Fifth Wheel Trailer
- Video: Review of etrailer RV Parts and Accessories - Spring-Loaded Pull Pin - RVLG-SPP
- Search Results: waste water tanks
- Search Results: waste tanks
- Q&A: Replacement Landing Gear Motor For a 2021 Keystone Springdale 5TH Wheel Camper
- Q&A: What is the Difference Between etrailer 8,000 lb Landing Gear Sets
- Q&A: Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
- Video: Review of TorkLift Battery Boxes - Trailer Battery Box - Camper Battery Box - TLA7700L
- Video: Review of Lippert Components - Trailer Jack,Camper Jack - LC141893
- Q&A: Will The Lippert Motor 142178 Work With the Landing Gear Set RVLG-8HDL
- Search Results: landing gear
- Search Results: gooseneck jack
- Search Results: gooseneck
- Search Results: trailer jack
- Video: Bulldog Square Jacks Rebuild using Replacement Screw and Nut Assembly
- Shop: RV Camera