Lippert High Speed Stabilizer Jack Mounting Hole measurements.

Question

Question:

By current lippert jacks are only 16 inches wide. Will this jack 20 inches line up with existing holes on my 2014 Flagstaff 5th wheel 8526IKWS?

asked by: Sam C

0

Expert Reply:

Good question, I did some research on this.

**Lippert High-Speed Power Stabilizer Jack - Black Waterproof Switch Kit - 30" Lift # LC298707.

The mounting locations on this unit are 68-11/16" from center-hole to center-hole. If you can get a measurement of your current units mounting locations this will let you know if they are spaced the same.

The parts department at Lippert tells me that the mounting holes are 16.81 inches apart on the ends.

So the mounting holes are 68-11/16 inches long and 16.81 inches wide.

expert reply by: David B

0

Answer 1

To replace your Lippert electric RV stabilizer I suggest their latest model #LC298707 which offers faster operation and lighter weight than many older models. This single-motor unit extends up to 30-inches and it should match the existing mounting…

view full answer...

Answer 2

For your Lippert Components Power Stabilizer Trailer Jack #LC298707 the wiring is pretty simple. There are two wires that come out of the motor and they are both used as power or ground depending on the direction you want to turn the motor. To…

view full answer...

Answer 3

The Lippert High-Speed Power Stabilizer Jack part #LC298707 should work great on a Jayco Jay Flight. They can be installed in either the front or rear of the trailer or both. They will simply bolt right-up to the frame for an easy install although…

view full answer...

Answer 4

The 20 amp fuse you are looking for on the #LC298707 is a fuse holder like what you can see in the attached diagram.

view full answer...

Answer 5

In regards to the Lippert Components High-Speed Power Stabilizer Jack like part #LC298707, the first thing I would do is check voltage on your battery to make sure it is above 12.4 volts. If it is not then you have a dead battery and it will need to…

view full answer...

Answer 6

There are a couple potential reasons why the back Lippert Power Jack #LC298707 on your trailer won't extend or retract even with the motor running. It's possible that it may have been over-extended or something internally has been stripped or…

view full answer...

Answer 7

It sounds like you have the B&W Companion fifth wheel hitch, part #BWRVK3500, that fits into the B&W Turnoverball gooseneck hitch. There isn't an adapter to make the square gooseneck shank fit into the round factory gooseneck hole on your…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Answer 12

A tow package for a vehicle is usually a frame mounted trailer hitch and trailer wiring on a vehicle like your 2002 Dodge Dakota. If you have those two things you could pretty easily assume you have the tow package. Or, you can take the VIN of your…

view full answer...

Lippert High Speed Stabilizer Jack Mounting Hole measurements.

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching