Stainless Polar Polished Stainless 270º Door Hinge

Question

Question:

I am lookig for the following item 2212-SSP Polar Hardware Square Corner Hinge Polished Stainless Steel - 12 270 degrees

asked by: Willys V

0

Expert Reply:

The # PLR2212-SSP is the hinge you're looking for. Polar's part number is 2212-SSP, our part number is # PLR2212-SSP. It's the same exact part, but we add a prefix onto it for our inventory system.

You can see a product description video for the hinge by clicking the provided link.

expert reply by: Mike L

0

Answer 1

I have attached for you below a dimensional drawing of the Square Corner Hinge with Reverse Bracket part #PLR2212-SSP provided from the manufacturer. This is the only dimensional drawing we offer for this product but if there is something else you…

view full answer...

Answer 2

For replacement hinges we have a few options depending on the material and rotation you are looking for. For example, the Square Corner T-Strap Hinge w/ Reverse Bracket #PLR2216-SSP is stainless steel and rotates 270 degrees. There are some other…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side.…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Stainless Polar Polished Stainless 270º Door Hinge

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching