Hitch Locks for Kuat Transfer V2 Bike Rack

Question

Question:

I need a hitch lock for my Kuat V2 Transfer - 1 bike - 2 hitch mount. Do you sell one that will fit this size? Thank you.

asked by: Jonathon H

0

Expert Reply:

The hitch lock you need for the Kuat Transfer V2 Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount item # KU64FR is the Hitch Lock for Kuat Bike Racks item # HL2 if you have a 2" hitch and the item # HL1 if you have a 1-1/4" hitch.

expert reply by: Jerred H

0

Answer 1

For a replacement hitch pin for your Kuat Transfer V2 for a 1-1/4" hitch, you will need the Hitch Lock for Kuat Bike Racks - 1-1/4" Hitches #HL1. This particular pin has a diameter of 3/8 on an inch and an overall length of 5-3/4 inches.

view full answer...

Answer 2

The correct hitch lock for your Kuat Transfer V2 Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount #KU64FR is the Hitch Lock for Kuat Bike Racks - 2" Hitches #HL1. This will allow you to lock the Transfer V2 to your vehicles…

view full answer...

Answer 3

The Kuat Transfer V2 Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount #KU64FR uses the #HL2.

view full answer...

Answer 4

If you are installing the Kuat Transfer V2 1-bike carrier #KU64FR onto a 2" hitch receiver, then you will want to use Hitch Lock #HL2. If you are installing this bike carrier onto a 1-1/4" receiver then use Hitch Lock #HL1. If you are…

view full answer...

Answer 5

I called and spoke with my contact at Kuat. He stated that the Bike Rack Hitch Lock for 1-1/4 Inch Racks, #HL1, is made of stainless steel. That would include the 5/16 inch diameter pin and the lock itself. There are no plastic pieces on the lock or…

view full answer...

Answer 6

The only difference between the #HL1 and #HL2 hitch lock is the diameter. HL1 is 3/8" in diameter and the HL2 is 1/2". Measure the diameter of the hole you have to see which one is closer. If the hole is more than 1/2" you can use…

view full answer...

Answer 7

To add a lock to the hitch part of your Kuat Transfer V2, part #KU74FR or part #KU84FR, you need the part #HL1 for a 1-1/4" hitch receiver or part #HL2 for a 2" hitch receiver, like what you said. Attached is a review video where we use the…

view full answer...

Answer 8

If you are using the Kuat Transfer V2 Bike Rack for 1 Bike #KU64FR for a 2-inch hitch, I confirmed with Kuat that you will need the #HL1 because of the 1-1/4 adapter sleeve that comes with the rack.

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Hitch Locks for Kuat Transfer V2 Bike Rack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching