Adjustable Cushioned Shocker Hitch With 2 Ball For a 2 Receiver With 4 of Drop

Question

Question:

I need an adjustable hitch that fits a 2inch receiver. I only need 3 - 4inch of drop and am interested in the shocker hitch. My trailer weight is 3k and tongue weight is 350lbs. I want something that gives me the most ground clearance and only need a 2inch ball. What do you recommend?

asked by: Don P

0

Expert Reply:

Since you mentioned the Shocker Hitch I am assuming that you are wanting a cushioned hitch. The Shocker XRC Cushioned Adjustable Drop Ball Mount with 2" Ball # SHK22ZR is adjustable from 4-1/2" to 7-1/2" of drop. This will only have the one 2" hitch ball.

expert reply by: Bud M

0

Answer 1

The replacement hitch ball for the Shocker Hitch XR Adjustable Drop Hitch is part #A-90 and has a 1-1/4" shank. All of the Convert-A-Ball hitch balls have a 1" shank so you'll either need to use one of the hitch ball kits,…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 4

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Adjustable Cushioned Shocker Hitch With 2 Ball For a 2 Receiver With 4 of Drop

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching