Replacement Brake Actuator for UFP-47729 or Dexter 099-075-00

Question

Question:

Do you sell brake actuator for boat trailer or rebuild kit. Here is part #s UFP-47729 or Dexter 099-075-00

asked by: Ravi S

1

Helpful Expert Reply:

For your application I recommend replacing your brake actuator with the Dexter DX7.5L A-60 Brake Actuator # DX27FR. This is a bolt-on application rated for 7,500 lbs and is compatible with a 2" hitch ball. UFP is owned by Dexter now and this is the replacement for the A-60 and A-70 couplers (which is what you have).

Attached is a review video for you to check out.

expert reply by: Jon G

1

Answer 1

For a disc brake model with an electric reverse lockout solenoid you can use #099-175-20.

view full answer...

Answer 2

The Dexter #DX27FR would make a good replacement for trailers weighing less than 7500 lbs. The coupler is compatible with a 2 inch trailer ball, so if your trailer meets those criteria, the #DX27FR would be an excellent choice. UFP is now owned by…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Replacement Brake Actuator for UFP-47729 or Dexter 099-075-00

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching