Hitch and Lock for 2022 Winnebago Revel Motorhome

Question

Question:

I need a trailer hitch lock that will work on a Revel Van. Any recommendations?

asked by: Jeanie B

0

Expert Reply:

Since the 2022 Winnebago Revel is built on a long wheelbase Mercedes Sprinter chassis you could use the Curt hitch part # C13388 for a hitch and then for a hitch lock the # HRLHP2 would work great.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 3

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 6

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 9

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 10

Thanks for the picture of what you have and the info you listed. The correct wheel you need is the part #AM20794 that you referenced.

view full answer...

Answer 11

Yes, the Furrion Automatic Transfer Switch #F30ATS has a wiring diagram on the inside of the cover. I've attached a picture of the diagram as well as a picture of the terminals with their functions.

view full answer...

Answer 12

90-120 ft lbs of torque is probably about right for your trailer rims. If you check out the lug nut torque chart that I attached you will see that nearly all of the torque specs are that and higher.

view full answer...

Hitch and Lock for 2022 Winnebago Revel Motorhome

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching