Availability of Base Plate Kit for the 2009 Chevrolet Malibu Sedan LTZ

Question

Question:

we are looking for a base plate to fit our car

asked by: 2009 m

0

Expert Reply:

The correct base plate kit for your 2009 Chevy Malibu LTZ is the Roadmaster EZ Base Plate Kit, item # 523145-5, and can be used with most standard tow bars.

Along with your base plate kit you may need wiring for your vehicle and this can be accomplished with a Tail Light Isolating Diode System with Wiring Harness, item # 38955, or a RoadMaster Tail Light Wiring Kit with Bulbs, item # RM-155, or a set of Magnetic Towing Lights, item # RM-2120.

expert reply by: Robert G

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The instructions for the Demco Tabless Base Plate Kit #DM77YV are being added to page but I'll also send them to you separately. In the instructions they only show that the air dam needs a chunk cut out and that the shutters would remain. The…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 12

Here are the steps to prepare your 2023 Ford Bronco Big Bend for flat towing. The transfer case and transmission will be in neutral with the ignition off. This information is in your owners manual. Switching Neutral Tow On 1.Switch your vehicle to…

view full answer...