Is Pintle Hook of B&W Tow & Stow BWTS10055 Available Separately

Question

Question:

Can I buy just the pintle adapter for the bandw tow and stow. I already have the hitch with a dual ball set up. Thank You

asked by: Mike H

0

Expert Reply:

The pintle hook attachment is not available for separate purchase. So while I know this was not the news you were wanting to hear, to get the pintle hook attachment you would need to get the pintle hook and shank, the B&W Tow & Stow Pintle Hook with 2" Ball - 2" Hitches - 10,000 lbs/16,000 lbs # BWTS10055.

expert reply by: Kyle S

0

Answer 1

Yes you can. If you got the B&W Tow & Stow Pintle Hook with 2-5/16" Ball #BWTS10056 you could use the #BWTS10051 as a replacement 2 inch ball when you needed it.

view full answer...

Answer 2

Yes, you're on the money because the most popular B&W Tow & Stow ball mount for 2 inch hitchers is indeed the one that has a maximum of 5 inches of drop or 5-1/2 inches of rise. There are actually two versions of this, one being a 2-ball…

view full answer...

Answer 3

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 4

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 7

We do have 205/75R14 size radial tires that have a load range of D and a speed rating of at least 81 mph. Out of our available selection I recommend going with the Kenda Karrier #AM10235. This tire has a max load rating of 2,200 lbs at 75 psi and a…

view full answer...

Answer 8

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 9

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 10

The Correct Track Trailer Alignment and Lift Kit part #RR23QX offers a 1-1/4" or 2-1/4"lift so if the hitch height height is lower than the vehicle hitch height you can use this kit to bring the trailer level with the vehicle and eliminate…

view full answer...

Answer 11

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...

Answer 12

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Is Pintle Hook of B&W Tow & Stow BWTS10055 Available Separately

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching