Is Additional Bolt Needed For Stabilizer Jack TJ01RT

Question

Question:

Ill be using 3 of these on a toy hauler ramp while loading my Harley trike. Once extended, wouldnt a bolt be recommended through the aligned holes as a safety feature to prevent accidental collapse?

asked by: Bob R

0

Expert Reply:

You will not need an added bolt for the Stabilizer Jack # TJ01RT when they are being used. So long as you are within the capacity of the jack, an accidental collapse is not a worry as they are designed to handle the weight without any added hardware and will be completely stable.

The only thing you might want to consider is the handle that allows you to fine-tune the height of the jack, which is the Handle Rod for etrailer and Ram Stabilizer Jacks # SJ-100-HD.

expert reply by: Kyle S

0

Answer 1

Installing the Stallion Stabilizer Jacks, #288-01892-2, if not welding in place, it is best done with grade 8 bolt and lock nut. Large self tapping screws have been successfully used by many to attach stabilizer jacks as well, but I suggest using…

view full answer...

Answer 2

In order to install the Stallion Stabilizer Jacks part #288-01892-2 on an aluminium frame trailer you will want to use stainless steel fasteners which can be obtained from a local hardware store though they will more less cost effective than standard…

view full answer...

Answer 3

The single jack part #TJ01RT is the same jacks that come with the pair of jacks #TJ01RT-HD. Also, the part #TJ01RT-HD includes a steel bar #SJ-100-HD for fine tuning the height of the jack. Check out the review video for more info as well.

view full answer...

Answer 4

The Stabilizer Jacks - 6-1/4" Drop Leg Travel #TJ01RT-HD that you mentioned are not spring loaded. This jack uses a series of internal steel notches to be able to give you the perfect height adjustment for your trailer, while still providing a…

view full answer...

Answer 5

Good question. The Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 1 #TJ01RT doesn't come with the Replacement Handle Rod for etrailer and Ram Stabilizer Jacks - 650 lbs #SJ-100-HD which does come included in the kit…

view full answer...

Answer 6

There many possible ways to mount a stabilizer jack such as the #TJ01RT-HD you looked at. Mounting them in the orientation shown the diagram would tend to work a bit better to stabilize the trailer against side to side movement, while having the…

view full answer...

Answer 7

The drop leg on the Stallion Stabilizer Jacks #288-01892-2 that you referenced is held securely in place by a spring-loaded lever. The leg cannot physically drop unless the lever is pushed down by hand so you don't have to worry about a big bump…

view full answer...

Answer 8

As you can see by the accompanying photos, the Stallion Stabilizer Jacks #288-01892-2 are very similar to the Atwood 82298 jacks. They are drop leg jacks with 7 inches of drop leg travel, an extended height of 22-1/4 inches, a lift capacity of 650…

view full answer...

Answer 9

I didn't receive your photos, but the manner in which you attach the e-track to your trailer deck will completely depend on what the deck is constructed of and where exactly on the deck you'll be placing the e-track. Without knowing any…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...