Could Inner Tube of Bulldog Gooseneck Coupler # BD0289800300 Fit Square 4 inch Outer Gooseneck Tube

Question

Question:

Is this compatible with a Big Tex 25GN. I have the same square tube but I only have one holding screw, not the two in the front and one in the rear as shown here.

asked by: Owen

0

Expert Reply:

The inner tube of the Bulldog Gooseneck Coupler # BD0289800300 would fit your 4 inch square outer coupler jack coupler tube. The amount of bolts would not be an issue.

expert reply by: Jameson C

0

Answer 1

The outer tube of the Bulldog #BD0289800300 Gooseneck Trailer Coupler measures 20 inches long as shown in the diagram that Bulldog provided for me. The outer tube is 4-1/2 inches square. The inner tube is 4 inches square and measures 31 inches long.…

view full answer...

Answer 2

The B&W Extend-A-Goose Gooseneck Coupler, part #BWTEXA4200 you referenced is designed to be able to attach to the inner tube on a gooseneck trailer and provide an additional 10 inches of clearance from your truck cab for your trailer. This…

view full answer...

Answer 3

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

I really wish we had replacement parts still for the Atwood couplers but since they've been out of business for so long we don't have any way to get the parts you are wanting.

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

If by serial number you mean VIN and the trailer manufacturer is still in business then yes, you would likely be able to obtain the bearing numbers from the manufacturer. If none of the above are true, then the only other way to determine which…

view full answer...

Could Inner Tube of Bulldog Gooseneck Coupler # BD0289800300 Fit Square 4 inch Outer Gooseneck Tube

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching