Weight Capacity Of 3" B&W Turnoverball Gooseneck Trailer Ball

Question

Question:

Can you post a photo of the top of this 3" ball so I can see the rating stamped on it?

asked by: Eric

0

Expert Reply:

The 3" Hitch Ball for B&W Turnoverball Gooseneck Trailer Hitch # BWGNXA2025 does have a rating of 40,000lbs. Be sure to verify that you do not exceed any weight ratings for your vehicle or hitch system.

I have included an image sent if from one of our reviews that shows the rating stamped in the hitch ball.

expert reply by: Bud M

0

Top Of Hitch Ball
(click to enlarge)

Answer 1

The Reese Elite Series 3-Inch Gooseneck Hitch Ball #RP19314 is intended for the Ford and Ram factory gooseneck hitches but for the factory hitch in your 2017 GMC Sierra 3500, which is made by Curt, we do not have a 3-inch ball. I confirmed with Curt…

view full answer...

Answer 2

I checked with my contact at the manufacturer regarding the Over the Seal Strap Hinge #PLR2116. It does not have a particular weight rating. This unit is designed to bridge door molding or a door seal. It is made in the USA and made from high quality…

view full answer...

Answer 3

I attached a picture that has as many of the dimensions as I could think of for the #BWGNXA2025 that I could think you might want.

view full answer...

Answer 4

The height of the square part the slides into the gooseneck hitch on the part #BWGNXA2025 measures 4 inches.

view full answer...

Answer 5

The 2-5/16" Gooseneck Coupler Head #291300 that you referenced is a gooseneck hitch coupler. It could be used with a tripod stabilizer if you had one but it's main function is for connecting a gooseneck trailer to a gooseneck ball in the bed…

view full answer...

Answer 6

The 2-5/16 inch Gooseneck Coupler Head with 1/2 inch Lock Pin, 30,000 lbs., item #291300, is cast construction and will require that a qualified weldor with experience in welding cast materials be utilized to attach the coupler to your equipment.…

view full answer...

Answer 7

The shaft of the B&W Turnoverball Adapter, #BWGNXA4025, measures 4-1/4 inches long from the base and it is 2-1/2 inches by 2-1/2 inches square. This adapter was specifically designed to fit in a B&W Turnoverball gooseneck trailer hitch.

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Weight Capacity Of 3" B&W Turnoverball Gooseneck Trailer Ball

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching