Replacement Motor for Kwikee 42 Series Electric RV Steps

Question

Question:

But I believe it is not an Igml motor. The Step Control LC379146 you recommend for Series 42 is an Igml Controller Will there be an issue with these two items working together?

asked by: Dean

0

Expert Reply:

In October of 2004, Kwikee began shipping steps with an integrated motor/gear box/linkage (IMGL). If yours is older than 2004 then you should use item # LC379146. The Replacement Motor for Kwikee 42 Series Electric RV Steps item # LC379167 you referenced fits step series 42. These parts will have no issue working together.

The IGML motor is Replacement Motor for Kwikee Electric RV Steps - 12V item # LC379147. The replacement module you would need is item # LC379605.

expert reply by: Jerred H

0

Answer 1

The correct step control for you is the Lippert Components Kwikee Step Control with Override and PKD part #LC379605 based on the part number you mentioned and the picture you mentioned.

view full answer...

Answer 2

If you are currently using 909510001 then you will need #LC379605. The other one, #LC379146, is for pre-IMGL steps. IMGL stands for integrated motor/gear box/linkage. In October of 2004, Kwikee began shipping steps with an integrated motor/gear…

view full answer...

Answer 3

The correct replacement for your Kwikee 909510000 step control is Lippert part #LC379146.

view full answer...

Answer 4

It doesn't look like the pictures came through, however, if you have the step series 22, 23, 27, 28A, 30, 32, 33, 34, 35, 36, 38, and 40, with the "A" linkage, you can use the Replacement Gear Box and A Linkage for Kwikee Electric RV…

view full answer...

Answer 5

They replaced your Kwikee step with a coach step. It really isn't an issue to do so just the assembly is different for the gear and motor than your previous step. The coach steps often have a separate switch inside the motorhome to turn off the…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Replacement Motor for Kwikee 42 Series Electric RV Steps

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching