Replacement Barrel Clips For The Replacement Step Pad For Westin Aries Oval Nerf Bars

Question

Question:

When installing my replacement step pads AA2090139 4 of the clips fell into the nerf bar hole. I had no problem with the other 3 pads, just the one. I need 4-5 clips sent to me. Thank you.

asked by: Troy C

0

Expert Reply:

You can find the replacement barrel clips here with # 23-0002, for your Replacement Step Pad for Aries 3" Wide Oval Nerf Bars # AA2090139.

expert reply by: Bryce D

0

Answer 1

While we have options for you, the pads with 4 holes you asked about, the Replacement Step Pad for Aries 4" Wide Oval Nerf Bars #AA2090133 will not work as replacements. The option that may work is the Replacement Step Pad for Aries 3" Wide…

view full answer...

Answer 2

I went out to our warehouse to take a look at the Aries Replacement Step Pad #AA2090139 that your referenced and measured a distance of right at 3-3/4" between the first two pegs, on center. While out there I went ahead and measured the spacing…

view full answer...

Answer 3

The Aries replacement pads are commonly tube step part number specific. I'd need to know what bars you have now to for sure be able to determine what you might need.

view full answer...

Answer 4

I attached a link to a page that has all of the step pads we offer but I can't really tell what you have since your picture is so dark. Maybe a brighter picture would be helpful.

view full answer...

Answer 5

Since you have what looks like the Aries Round Nerf Bars 3 inch diameter #AA206003-2 on your 2002 Acura MDX the correct step pad would be the part #AA2090139.

view full answer...

Answer 6

The closest we have is Replacement Step Pad for Aries 3" Wide Oval Nerf Bars #AA2090139. This is about 20" long and has peg spacing similar to the measurements you gave me. This has 5 pegs; there is a distance of 3-3/4" between the…

view full answer...

Answer 7

I've attached the measurements for the Westin Barrel Clips #23-0002. You would need holes approximately 3/8 inch minimum and 7/16 inch maximum for these clips to work properly.

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 12

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Replacement Barrel Clips For The Replacement Step Pad For Westin Aries Oval Nerf Bars

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching