How To Remove Old Door Latch From Trailer Door

Question

Question:

How to remove the old door latch for my pop up trailer

asked by: Michael

0

Expert Reply:

To remove your door latch like # 295-000019, you'll need to remove the 2 screws by the strike plate on the door, and the 3 or 4 screws located on the backside of the latch. From here, you can remove the backing plate, and then push the latch out from the other side of the door.

To reassemble the new latch to your door, just repeat the above steps in reverse order.

expert reply by: Bryce D

0

Screws To Remove
(click to enlarge)

Pulling Latch Out
(click to enlarge)

Answer 1

The Global Link RV Entry Door Locking Latch Kit #295-000019 that you referenced would be the correct fit for your 2010 Keystone Montana as this is a fit for standard RV doors like what your Montana has. I attached a review video link for this latch…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 4

We may have some potential options for replacing the tack room door lock on your Featherlight trailer. Is the 5" L x 5" H dimension you gave for the door cutout or the lock itself? The best way to find the right replacement lock is to go by…

view full answer...

Answer 5

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

I contacted Trimark in regards to a replacement part for the Trimark 030-0900. 030-0900 is actually a series number not a specific part number. To find the part number you will need to take the interior handle completely off the unit. On the back…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

I think I have a solution for you in the Global Link RV Entry Door Locking Latch Kit, #295-000021 for white or, #295-000019 for black. This latch kit measures 3.47" wide x 4.28" tall, fits doors that are 1-1/4" to 1-1/2" thick,…

view full answer...

Answer 10

We have the following Gen-Y shock absorbing 5th wheel pin boxes which are compatible with the Lippert Rhino pin box bolt pattern. The weights listed below are the maximum capacities the pin box is capable of supporting. 21,000 lbs - 3.5K TW #GY86GR…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

How To Remove Old Door Latch From Trailer Door

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching