Wiring Diagram For Turn Signal Switch For Peterson Combination Stop And Turn Signal Lights

Question

Question:

DIAGRAM HOW TO WIRE PM 500 SIGNAL SWITCH

asked by: Jesús R

0

Expert Reply:

The wiring color code for the Turn Signal Switch for Peterson Combination Stop and Turn Signal Lights # PM500 is as follows:

Red- Front right
Black- Front rear
Pilot Blue- Flasher - Fuse - 12 volt power
Load Yellow- Flasher
Gray/Black- Stop light switch
Gray- Left rear
Green- Left front

expert reply by: Bryce D

0

Wiring Diagram
(click to enlarge)

Answer 1

The following wires on the Turn Signal Switch #PM500 are for the following functions: Red - Right Front Black - Right Rear Pilot Blue - Flasher - Fuse - 12V Power Load Yellow - Flasher Gray/Black - Stop Light Switch Gray - Left Rear Green - Left…

view full answer...

Answer 2

I spoke with Peterson, and they informed me your lights may not be working because you are going to need to use a 3 prong flasher with your: -Turn Signal Switch for Peterson Combination Stop and Turn Signal Lights #PM500. Additionally, if you are…

view full answer...

Answer 3

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Wiring Diagram For Turn Signal Switch For Peterson Combination Stop And Turn Signal Lights

Product Page this Question was Asked From

Continue Researching