How Much Will Oval GloLight LED Trailer Tail Light Stick Out From Trailer Frame

Question

Question:

From the mounting surface, how far do these lights stick out?

asked by: Yarrow R

0

Expert Reply:

The GloLight LED Trailer Tail Light # STL111RB will stick out about an inch when installed. It's pretty minimal and also the standard size for this style of light.

expert reply by: Jon G

0

Answer 1

You'd have to drill a pretty large hole to fit the plug ends of the #98174LED through the brackets. I'd rather recommend you zip tie the harness to a much smaller hole instead of drilling the roughly 1-1/4 inch hole you'd have to drill,…

view full answer...

Answer 2

Although the Snap-on Reflector Ring, #A78RXB, will not fit the STL178 series lights like the Optronics GLOLight LED Stop/Turn/Tail Light #STL178RFPB, I do have a solution for you. Take a look at the Sealed, 6-1/2" Oval LED Trailer Stop, Turn and…

view full answer...

Answer 3

Yes, it is possible to buy just the wiring harness for the LED Light Kit for Draw-Tite, Tow Ready, Pro Series, and Rola Railed Cargo Carriers item #98174LED. It is the Optronics Replacement Cargo Carrier Light Harness item #WHCETR1B.

view full answer...

Answer 4

You could use the LED kit part #98174LED to add the lights and wiring to your bike rack and then use the bracket #BK70BB and you'd be set. You'd have to attach the brackets to the bike rack and then once installed the lighting harness would…

view full answer...

Answer 5

Yes, if you wanted to install the #STL111RCB in the opening of the #AL65-0 all you would need is the correct grommets, part #a70gb.

view full answer...

Answer 6

Since there isn't a specific light kit that will fit the Curt carrier #C18153, what you will need to do is use a light kit like #98174LED, and then add 2 brackets part #BK70BB as they work with 6-1/2 inch oval lights. You will also need some…

view full answer...

Answer 7

To add a lighted license plate mount to the LED Light Kit #98174LED on your cargo carrier I recommend the Optronics #LP55CB. The bracket simply gets attached to the carrier with a couple of screws (not included) and the wiring harness can be tied…

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

How Much Will Oval GloLight LED Trailer Tail Light Stick Out From Trailer Frame

Product Page this Question was Asked From

Continue Researching