Installation Instructions for Replacement Cover for Pace Edwards JackRabbit Hard Tonneau Cover

Question

Question:

I have an older model of this cover and it attaches to the spring drum with about 10 screws. I would like to see the install instruction for this apparently newer version as I may have to see if it will work. Mine doesnt seem to have a model # anywhere that I can see. It is on a 2005 F150SD. My main concern is how do you hold the spring drum in place?

asked by: Mike

0

Expert Reply:

I spoke to my contact at Pace-Edwards he said that when installing a replacement cover, like the Replacement Cover for Pace Edwards JackRabbit Hard Tonneau Cover # 311-TRPT1472-2007, the typical way he recommends to keep the tension on the spring is to have a second person to help. One holds the spring tube, while the other feeds in the new fabric panel assembly and handle. Then attach the new part to the spring tube.

expert reply by: Thomas M

0

Answer 1

No, the Replacement Vinyl and Aluminum Cover for Pace Edwards JackRabbit Hard Tonneau Cover #PE94CV is not going to work with your 2018 GMC Sierra 1500. Instead, you're going to want to use the Replacement Panel Assembly for Pace Edwards…

view full answer...

Answer 2

I just spoke with my rep at Extang and he confirmed that the item #EX37560 is the full tilt replacement cover for your 1997 Chevrolet S-10 fleetside truck.

view full answer...

Answer 3

I spoke with Pace Edwards and they sent me an install instructions sheet for replacing the cover of a Pace Edwards JackRabbit Tonneau Cover. I attached the instructions to this page for you to check out. You do have to rewind the cover's spring…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 6

Your 265/70R17 size tire is around 31-1/2 inches in diameter. You want to make sure the tire cover you get is large enough and doesn't have to be stretched over the tire. I'd rather have one that's slightly loose than one that tears…

view full answer...

Answer 7

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 8

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 9

From your question it sounds to me like someone has cut off the tow package plug on your 2005 Ford F-150 and wired in a 4-way connector. In this case you could use the Hopkins Adapter 4-Pole to 7-Pole and 4-Pole, #37185 which will give you a 4-way…

view full answer...

Answer 10

There is a solution for you, but the lift kits you referred to such as #K71-725-02 will not work with welded on torsion axles. The best option is for you to simply remove your torsion axles and use the Timbren Axle-Less Trailer Suspension System…

view full answer...

Answer 11

I trust regular axles with leaf spring suspension more than torsion axles only because I can see what is going on with the suspension and can fix any issues should they arise. With a torsion axle though there really isn't any maintenance you have…

view full answer...

Answer 12

Yep, you're exactly right; the distance from the center of the hitch pin hole to the welded gusset is indeed four inches on the Curt Ball Mount for 2" Hitches #C45112. So if that's the amount you need for it to work without hitting the…

view full answer...

Installation Instructions for Replacement Cover for Pace Edwards JackRabbit Hard Tonneau Cover

Product Page this Question was Asked From

Continue Researching