Replacement Camera for Voyager WVOS541 System

Question

Question:

Is the Voyager camera WVH100 compataible with my system and can the camera only be purchased separately?

asked by: Robert W

0

Expert Reply:

Yes, the Voyager WiSight RV Observation Camera - Wireless item # WVH100 is compatible with your Voyager WVOS541 System. The camera is sold separately. If you are wanting to replace the Voyager Monitor down the road it is item # VOM719WP.

expert reply by: Jerred H

0

Answer 1

The pre-wiring of Furrion pre-wired RVs is basically just two wires as well as the Voyager harness like part #PSVCWVCMS130AP. One wire is the power wire which is the running light circuit and then the other is the ground so it really would just be a…

view full answer...

Answer 2

My first thoughts on your Voyager WiSight Wireless System, #WVOS541, are, there is an issue getting a strong wireless signal. You've checked power to the monitor but what about the camera and antennae, please verify that too. If you are getting…

view full answer...

Answer 3

To connect back up lights you need to have a 7-way trailer connector on both your trailer and tow vehicle. On a 7-way the reverse lights are powered by the center pin. To connect reverse lights to the trailer's 7-way you can use 16 gauge wire…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Replacement Camera for Voyager WVOS541 System

Products Referenced in This Question

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching