What Are the Dimensions of the Dutton-Lainson Covered Hand Winch Trailer Winch 2,600-lbs

Question

Question:

Hi I notice you have a front view with dimensions of the Dutton-Lainson Covered Hand Winch on your site. I am drawing up a trailer for a customer and need side view dimensions of this winch so that I can position it correctly in the Winch Post.

asked by: Joe T

0

Expert Reply:

The Dutton-Lainson Covered Hand Winch # DL17085 is 13-1/2" long/wide when looking at the side. I added a review video of this winch that shows more of its measurements for your to check out.

expert reply by: Erik B

0

Answer 1

The bolt hole spacing as well as the bolt hole pattern is different when you compare the #DL14627 (which is the 1802A) to the #DL15440 (3200A). The overall dimensions differ as well. I am attaching some pictures showing the bolt hole measurements as…

view full answer...

Answer 2

I attached a picture that shows the dimensions of the JIF winch #315-W2500D as well as another picture that shows the overall dimensions of the jack.

view full answer...

Answer 3

Fulton winches like the Fulton XLT 2-Speed Trailer Winch with Heavy Duty 20' Strap part #F142418 are made in Mexico according to Fulton. If you are looking for a winch made in the USA you may consider the Dutton-Lainson Covered Hand Winch part…

view full answer...

Answer 4

The mounting pattern for the Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed - Direct Drive - 2,000 lbs #DL14725 you were looking at is the exact same as your current DL1802A, but the overall dimensions of the winches are different. The…

view full answer...

Answer 5

Yes, the Hand Winch Strap with Safety Hook part #DL24251 will work just fine with the Dutton-Lainson Hand Winch part #DL14725. However, please note that you will be limited to the weight capacity of the winch which is 2,000 lbs because it is lower…

view full answer...

Answer 6

Generally when picking out a winch for a boat trailer the ratio is 2 to 1 meaning you would need a winch with roughly half the capacity as the weight of the boat. With good rollers and a short winching distance the ratio increases to 3 to 1, but with…

view full answer...

Answer 7

To get the cable to come off of the Dutton-Lainson Worm Gear Hand Winch, item #DL10974, you would need to crank the winch until the cable is all the way unwound from the winch drum and then continue cranking in the same direction until the cable is…

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

I spoke with my contact at Dexter and he said the 21-37 oil cap is obsolete and was replaced with the 21-36 oil cap, #RG04-270. This cap includes the o-ring and plug.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Are the Dimensions of the Dutton-Lainson Covered Hand Winch Trailer Winch 2,600-lbs

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching